• large 4-digit LC display with illumination
• TRUE RMS measuring method for industrial applications
• direct display of the current intensity in amperes
• safe operation with a distance of 1.8 m to the measuring point
• memory of measured values (HOLD/ MIN/MAX)
• automatic switch-off („APO“), can be disabled
• battery low-voltage indication
• measuring category CAT IV 600 V
• including protective pouch and batteries

• the integrated Volt sensor signalises phase voltages by means of an acoustic signal and a red LED signal
• it localizes cable breaks and defective lamps in exposed cables (cable reel, light chains) via the feeding side of the phase

• the integrated Volt sensor signalises phase voltages by means of an acoustic signal and a red LED signal
• it localizes cable breaks and defective lamps in exposed cables (cable reel, light chains) via the feeding side of the phase

• the integrated Volt sensor signalises phase voltages by means of an acoustic signal and a red LED signal
• it localizes cable breaks and defective lamps in exposed cables (cable reel, light chains) via the feeding side of the phase

• TRUE RMS measuring method for precise measuring results even for non-sinusoidal signal characteristics
• highest measuring category CAT IV 600 V for highest safety
• AutoV function for automatic AC/DC voltage detection and low input impedance (LoZ) to suppress capacitively/inductively induced voltages
• integrated Volt sensor for non-contact signalling of phase voltages and cable breaks in lines
• LC display with bargraph indication and background lighting

• basic measuring for current, voltage, resistance, continuity, diode, capacity and frequency
• automatic and/or manual measuring range selection
• safe current measuring up to 300 A AC via attachable current clamp adapter

• basic measuring for current, voltage, resistance, continuity, diode, capacity and frequency
• automatic and/or manual measuring range selection

• basic measuring for current, voltage, resistance, continuity, diode, capacity and frequency
• automatic and/or manual measuring range selection

• basic measuring for current, voltage, resistance, continuity, diode, capacity and frequency
• automatic and/or manual measuring range selection

• highest measuring category CAT IV 600 V allows measurements direct at the source of the low-voltage installation
• precise due to TRUE RMS measuring method

• highest measuring category CAT IV 600 V allows measurements direct at the source of the low-voltage installation
• precise due to TRUE RMS measuring method
• transmitting measuring results via optical USB interface
• delivery including software BENNING PC-Win MM 10

• large memory capacity of 1000 storage locations and 40000 storage locations for Data Log functions
• transmitting measuring results via optical USB interface
• delivery including software BENNING PC-Win MM 11

imple closing mechanism which can be operated with gloves
• green LED for stand-by mode, red LED for battery undervoltage
• measuring category CAT III 600 V
• including protective pouch and batteries

TRITEST®easy - ปากกาวัดไฟแบบไม่สัมผัส
ปากกาTest ไฟแบบไม่สัมผ้ส /ทดสอบ phase sequence ได้, Warranty 2 ปี TRITEST®easy - แบบไม่สัมผัส เช็ค AC mains ได้อย่างรวดเร็ว ทดสอบ phase / phase sequence ได้ ตรวจ phase sequence ในระบบ 3 phase แดสงผลด้วย LED มีเสียงเตือน เหน็บกระเป๋าได้คล้ายปากกา ใช้งานง่าย
>>>>ดูรายละเอียดหน้าถัดไป<<<<

TRUE RMS AC/DC milliampere current clamp multimeter
• ideal for troubleshooting in electrical installations, control systems, appliances and automotive electrical systems
• precise measurements of low AC/DC currents with highest resolution of 0.1 mA
• multifunctional use for voltage measurements (300 V AC/DC), resistance measurements (500 k) and continuity tests
• TRUE RMS measuring method
• compact dimensions with a clamp opening
of 23 mm
• memory of measured values (MAX/MIN/HOLD)
• high-quality protective pouch and set of 4 mm measuring lines included in delivery

• measurement of leakage currents and differential currents in electrical systems (VDE 0100) and devices (VDE 0701- 0702, BGV A3, BetrSichV ( = German Health and Safety at Work Regulations))
• highest resolution of 1 μA in the 6 mA measuring range
• measurement without switch-off during normal operation of the system/device, the perfect solution for preventive maintenance
• precise and reproducible measuring results up to 100 A
• optimum screening against external magnetic fields

• bipolar phase sequence test in three-phase mains
• measuring inputs for voltage, resistance, continuity, diode, frequency and temperature
• measurement of inrush currents (motors etc.)

• precise due to TRUE RMS measuring method
• safe current measuring up to 1000 A AC/DC
• highest measuring category CAT IV 600 V offering optimum safety

• precise due to TRUE RMS measuring method
• safe current measuring up to 1000 A AC/DC
• highest measuring category CAT IV 600 V offering optimum safety

• automatic selection of the correct measuring function for TRUE RMS voltage/current (AC/DC), resistance, continuity and diode test
• safe and easy operation – measuring errors due to incorrect measuring range selection are excluded
• short response time due to 5 scanning values per second
• voltage measurement with low input impedance (LoZ) to suppress capacitively/inductively induced voltages

• safe and non-contact measuring of high currents
• DC and AC current measuring up to 600 A AC/DC
• measurement of low currents (automotive, photovoltaics, industry)
• measuring inputs for voltage, resistance and continuity test
• precise due to TRUE RMS measuring method

• precise due to TRUE RMS measuring method
• safe current measuring up to 1000 A AC/DC
• highest measuring category CAT IV 600 V offering optimum safety

• safe and non-contact measuring of high currents
• DC and AC current measuring up to 600 A AC/DC

• safe current measuring up to 400 A AC
• measuring inputs for voltage, resistance, continuity and diode test

• safe current measuring up to 400 A AC
• measuring inputs for voltage, resistance, continuity and diode test

• safe current measuring up to 400 A AC
• measuring inputs for voltage, resistance, continuity and diode test
• integrated volt sensor signalises phase voltages by means of an acoustic signal and a red LED signal
• it localizes cable breaks and defective lamps in exposed cables (cable reel, light chains) via the feeding side of the phase

• easy and safe operation by means of keys
• automatic test procedure for polarity, open-circuit voltage, short-circuit current and insulating resistance
• RISO measurement with “PASS/FAIL” indication
• memory of measured values for 200 PV strings
• integrated real-time clock with date/time stamp for each measurement
• USB interface and download software for the preparation of test certificates in MS Excel®
• safe contacting even during energy supply of the PV system
• direct connection by means of MC4 and “Sunclix” connectors

• universal 4-in-1 measuring instrument for all testing and maintenance work as well as for economic efficiency analysis
• temperature-compensated PV reference cell for precise insolation measurement
• precise temperature measurement by means of high-precision sensors
• data logger for 5000 data records, including insolation and module/ambient temperature
• integrated real-time clock with date/time stamp
• USB interface and download software for the preparation of test certificates in MS Excel®
• data logger with energy-saving stand-by mode
• shock-absorbing protective rubber holster

• voltage testing up to 1000 V AC TRUE RMS/1200 V DC
• TRUE RMS measuring method
• low-volt range: 1.0 V to 11.9 V
• frequency indication up to 1000 Hz
• resistance measurement up to 300 kΩ
• conducting-state voltage measurement of diodes
• automatic LC display illumination by means of a light sensor

• acoustic continuity test with loud test buzzer and visual indication by means of yellow LED
• measuring point illumination by means of white high-power LED
• phase sequence test by means of green LED (left/right)
• detector for non-contact localization of cable breaks on exposed and live lines

• safe voltage testing up to 1000 V AC/DC
• direct display without actuating a push-button (high-impedance testing)
• load connection via push-button (low-impedance testing)
• battery-independent voltage indication from 50 V AC/DC on
• vibration alert in the test handle
• robust round housing with rubberized gripping surface for outdoor use (protection category IP 65)
• tested and approved in compliance with the current DIN EN 61243-3 (VDE 0682-401):2011 standard

• automatic testing procedure for devices of class I (key 1), class II/III (key 2) and line test (key 3)
• testing of cable reels, multiple distributors and device connecting cables with rubber connector
• measuring result with “pass/fail” information
• limiting values preset in compliance with DIN VDE standard
• indication of correct function key in case of incorrect operation and if the test sample is not switched on
• sufficient battery capacity (6 x 1.5 V, mignon, AA, IEC LR6) for > 2500 test samples
• three-phase test objects can be tested by means of optional measuring adapter

• mains operating mode for tests under operating conditions
• battery operating mode for mobile testing
• automatic testing procedure for devices of class I (key 1), class II/III (key 2) and line test (key 1)
• reduction of the ISO testing voltage to 250 V/ 500 V for devices with overvoltage arresters/electronic devices
• testing of RCDs with 30 mA
• measuring result with “pass/fail” information
• limiting values preset in compliance with DIN VDE standard
• indication of correct function key in case of incorrect operation, overload and if the test sample is not switched on
• sufficient battery capacity (6 x 1.5 V, mignon, AA, IEC LR6) for > 2500 test samples

• automatic testing procedure for devices of class I (key 1), class II / III (key 2) and line test (key 3)
• testing of cable reels, multiple distributors and device connecting cables with IEC connector
• reduced testing voltage for devices with overvoltage arrester
• note in case of incorrect selection of the testing procedure and if the test sample is not switched on
• suffi cient battery capacity for more than 2,500 test samples
• measuring result with „PASS / FAIL“ indication, preset limiting values

• automatic and auto-configurable testing procedures
• complete test sample/customer database can be stored on SD card and thus is directly available at the place of inspection
• management of large test sample inventories with more than 100000 storable device tests per 2 GB SD card
• direct entry via touchscreen and external keyboard/mouse
• measuring result with “pass/fail” indication and acoustic warning signal, if the test has been failed
• help function and schematic connecting diagrams
• separate 4 mm test sockets and IEC connector
• 3 x USB interface for PC, external keyboard and RFID reader/writer
• 1 x RS 232 interface for barcode scanner, printer and SD card slot
• free firmware update possible via SD card/USB stick

• safe current measuring up to 400 A AC
• measuring inputs for voltage, resistance, continuity and diode test

• safe current measuring up to 400 A AC
• measuring inputs for voltage, resistance, continuity and diode test

• safe current measuring up to 400 A AC
• measuring inputs for voltage, resistance, continuity and diode test
• integrated volt sensor signalises phase voltages by means of an acoustic signal and a red LED signal
• it localizes cable breaks and defective lamps in exposed cables (cable reel, light chains) via the feeding side of the phase

• safe and non-contact measuring of high currents
• DC and AC current measuring up to 600 A AC/DC

• safe and non-contact measuring of high currents
• DC and AC current measuring up to 600 A AC/DC
• measurement of low currents (automotive, photovoltaics, industry)
• measuring inputs for voltage, resistance and continuity test
• precise due to TRUE RMS measuring method

• precise due to TRUE RMS measuring method
• safe current measuring up to 1000 A AC/DC
• highest measuring category CAT IV 600 V offering optimum safety

• precise due to TRUE RMS measuring method
• safe current measuring up to 1000 A AC/DC
• highest measuring category CAT IV 600 V offering optimum safety

• precise due to TRUE RMS measuring method
• safe current measuring up to 1000 A AC/DC
• highest measuring category CAT IV 600 V offering optimum safety

• automatic selection of the correct measuring function for TRUE RMS voltage/current (AC/DC), resistance, continuity and diode test
• safe and easy operation – measuring errors due to incorrect measuring range selection are excluded
• short response time due to 5 scanning values per second
• voltage measurement with low input impedance (LoZ) to suppress capacitively/inductively induced voltages

• TRUE-RMS measurements up to 600 V, 600 A AC/DC
• effective power measurements up to 360 kW
• calculation of the power factor cos

• indication of the load type (inductive, capacitive)
• bipolar phase sequence test in three-phase mains
• measuring inputs for voltage, resistance, continuity, diode, frequency and temperature
• measurement of inrush currents (motors etc.)

• measurement of leakage currents and differential currents in electrical systems (VDE 0100) and devices (VDE 0701- 0702, BGV A3, BetrSichV ( = German Health and Safety at Work Regulations))
• highest resolution of 1 μA in the 6 mA measuring range
• measurement without switch-off during normal operation of the system/device, the perfect solution for preventive maintenance
• precise and reproducible measuring results up to 100 A
• optimum screening against external magnetic fields

• measurement of insulating resistance and calculation of the resulting leakage current
• testing voltages of 50 V, 100 V, 250 V, 500 V and 1000 V
• selectable limiting values for ISO measurement, green LED for “PASS”, red LED for testing voltage/external voltage
• resistance measurement with a testing current of 200 mA for testing protective conductor connections
• measurement of polarization index (PI) and dielectric absorption rate (DAR)
• switchable probe tip for triggering the measuring process
• internal memory for 100 measuring values per measuring function
• TRUE RMS voltage measurement with low-pass filter
• including case, switchable probe tip, silicone measuring leads, magnetic hook, alligator clips, rubber protective frame and batteries

• measurement of the protective conductor line and of the equipotential bonding line with a testing current of 200 mA
• measurement of the insulation resistance with testing voltages of 100 V, 250 V, 500 V and 1000 V
• line impedance and loop impedance measurement (optional without tripping of the RCD) with calculation of the shortcircuit current (PFC/PSC)
• complete testing of RCDs with nominal fault currents of 10/30/100/300/500/1000 mA
• measurement of contact voltage (without tripping), tripping time and tripping current (ramp test) of residual current operated device (RCD)
• phase-sequence testing in three-phase mains
• voltage measurement up to 500 V and online voltage monitoring

in addition to the BENNING IT 110 :
• testing of universal current-sensitive RCDs of type B
• current measurement (TRUE RMS) by means of current clamp adapter (optional)
• illumination measurement by means of lux sensor (optional)
• earthing measurement by means of three-wire measuring method (optionally with earthing set)
• integrated measured value memory for 500 measurements
• USB and RS 232 interface
• BENNING PC-Win IT 120 B software included in delivery

• measured value memory covering four levels: object/ block/ fuse/ measuring point
• bidirectional interfaces (USB / RS 232)
• upload of installation structures and download of measured values
• integrated real-time clock (measured value with date/ time)
• unambiguous „PASS“ / „FAIL“ indication by means of green/ red LED on the tester and on the switchable „Commander“ probe tip
• „Commander“ probe tip with „TEST“ and „MEM“ key as well as bright LED measuring point illumination
• connection for barcode scanner for identifying the measuring point and renaming the storage location
• help function with connecting diagram
• graphic display with background lighting
• power supply by means of six NiMH storage batteries (AA)
• device with integrated storage battery charging function
• delivery including case, storage batteries, measuring leads, charging cable, switchable „Commander“ probe tip, PC software and calibration recor

• continuity and semiconductor test by means of LEDs and loud test buzzer
• visual indication by means of three LED steps: 0 to 100 /1 k/10 k
 • acoustic indication via test buzzer up to approx. 100 
• external-voltage indication: 6 V to 400 V (LEDs / test buzzer)
• polarity test, single-pole external conductor test (phase) and non-contact cable break detector
• precise and powerful LED torch
• buzzer volume and brightness of the LED torch are individually adjustable
• integrated magnetic holder and belt clip at the rear of the housing

• indication of „clockwise“ and „counter-clockwise“ phase sequence by means of green / red LED
• indication of phase voltages L1, L2 and L3 by means of red LED
• voltage range: 400 V to 500 V AC (50 Hz to 60 Hz)
• luminous high-power LED torch
• integrated magnetic holder and belt clip at the rear of the housing
• including set of 4 mm test probes and alligator clip